How to Install a Tub
How to Install a Tub
Blog Article
How do you actually feel about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and also often, tiling abilities. Replacing an old bathtub with a new one is also a reasonably hard job. If the old tub is readily available, the task can relocate immediately; if you need to open a wall to remove the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the brand-new one. Make certain you have qualified on your own for the task and are comfortable attempting it. Instead of employing a professional to take over a halfway-completed project, it is better to consider using one prior to you begin. Opportunities are you might need a specialist plumber to make tube links.
This short article will certainly assist you set up a brand-new tub in your restroom if you have actually already bought a brand-new tub and also don't need to transform the arrangement of your previous water supply pipelines.
Your devices and product checklist need to make up the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather problematic because of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipelines. When the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin ensuring that the washers are in location in between the faucet and the sink. Secure the tap in position with the maker given backnut. Once the tap is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet ports. The previous kind needs to be attached to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub till the level checks out level.
To set up taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Activate the water as well as inspect all joints and new pipework for leakages and tighten them if necessary. Load the bath tub and also check the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling and sealing around the bath tub must wait until the bath tub has actually been utilized at least when as this will settle it right into its final position.
Planning for the Installation
To start with, the supporting framework provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to avoid strain on the tub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, resulting in complications with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before securing, to permit the activity experienced when the bathtub is in use. The sealant can break fairly early if you do not take into consideration this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader about How to Install a Bathtub, I was thinking sharing that post was necessary. Liked our entry? Please share it. Let someone else find it. We thank you for reading our article about How to Install a Bathtub.
Make An Appointment
Report this page